We are more than a roofing contractor in Cascade, we are a crew that plans access before it plans the install. Cascade sits at about 7,379 feet, above the 7,000 foot line the Pikes Peak Regional Building Department uses, which means roofs here must be designed for 57 pounds per square foot of ground snow load and 40 pounds per square foot on a flat roof.
As your roofing company in Cascade, Storm Guard handles mountain properties and the businesses along the pass. Residential roofing, commercial roofing in Cascade, gutters, and emergency tarping.
Cascade housing runs from older cabins and inns to year round homes tucked into the canyon walls. Steep pitches, mixed rooflines, and tight sites are normal here, and they change how we approach both roof repair and replacement.
Lodging, visitor attractions, and small businesses along the Ute Pass corridor need roofs that carry a real snow load without leaking into a guest room. See metal roofing in Cascade for the shedding option most canyon properties prefer.
Cascade gutters deal with pine needles and, after a heavy melt, a lot of water in a short window. We install and repair gutter systems with the capacity and the ice protection this elevation needs.
When a tree comes down or wind opens a ridge, emergency roof tarping keeps the weather out until a permanent repair can be scheduled around canyon access.
As your roofer in Cascade, we work out the practical questions first: where the truck goes, where material stages, and how we protect a steep slope below the work area.
We inspect the full roof, including the details that only matter at altitude: ice and water protection at the eaves, valley condition, and how snow is currently coming off the roof.
Our Cascade roofing contractors put the whole job in writing, including any access or staging costs, so a canyon lot does not produce surprises later.
We install to manufacturer specification using premium materials, engineered for the higher snow load that applies above 7,000 feet rather than the lower figure used down in the city.
After a thorough final roof inspection in Cascade, we clear the site completely, including the slope below the work, where debris tends to end up.
Storm Guard uses only the highest quality materials sourced from top manufacturers. In Cascade the conversation usually comes down to how a roof sheds snow, which is why standing seam metal is so common along the pass.
As your go-to roofer in Cascade, we build for snow load, slope, and canyon access. From roof replacement to gutters and emergency support, we do it all. Call us today for your consultation.
Yes. Cascade is about ten miles west of Colorado Springs on US Highway 24 and it is a standard part of our service area. As unincorporated El Paso County, permits run through the Pikes Peak Regional Building Department, and because Cascade sits above 7,000 feet the higher snow load design applies.
The Pikes Peak Regional Building Department sets its design criteria by elevation, with a 7,000 foot threshold. Cascade sits at roughly 7,379 feet, so the requirement is 57 pounds per square foot of ground snow load and 40 pounds per square foot on a flat roof, rather than the lower 43 and 30 pound figures that apply to Manitou Springs further down the pass.
At this elevation the tells are usually snow and moisture related:
Replacement usually makes sense when:
Longer than the same house would take in the city, and access is why. A straightforward Cascade home is typically two to three days once material is staged. Narrow shoulders and steep drives limit how much can be on site at once, and weather windows at this elevation are shorter.
Yes. We inspect, document with photographs, and meet the adjuster on site. That matters in Cascade because snow and ice damage is easy for an out of area adjuster to misread. We do not negotiate settlements, and Colorado law bars any roofer from paying or waiving your deductible.
A manufacturer warranty on the materials and our own workmanship warranty on the installation. At this elevation the installation details, particularly ice and water protection at the eaves, are what actually determine whether the roof performs.
Three reasons, and we itemize all of them: the higher snow load design, the steeper and more complex rooflines common in the canyon, and access. A house that a truck can park in front of is cheaper to roof than one at the top of a narrow drive.
Less than you might think. Color affects attic heat in summer, but in a canyon at 7,379 feet how the roof handles snow, ice, and ultraviolet exposure matters far more. We would rather talk about ventilation and eave detailing.
Because ventilation is what prevents ice dams. A warm attic melts snow on the roof surface, the water runs down and refreezes at the cold eave, and the resulting dam pushes water back under the shingles. Balanced intake and exhaust keeps the deck cold and stops that cycle.
At the eaves and in the valleys. Both are where snow and meltwater linger longest. Chimney and sidewall flashing is next, especially on older cabins where the flashing predates modern underlayment.
Often it is the best idea. A properly installed metal roof can last 40 to 70 years and sheds snow rather than holding it. On steep canyon lots we do discuss where the snow will land, because a roof that dumps a load across a walkway or driveway creates a different problem.
It is a common move once a roof passes roughly 15 years, and it means depreciation is deducted from any payout. Worth checking before winter rather than after a storm, particularly if your roof was installed before the current snow load requirements.
Always, on a full replacement. Flashing at valleys, chimneys, and sidewalls does the hardest work on a mountain roof, and reusing tired metal under new shingles is where leaks come back two winters later.
Unless otherwise noted, each use of "Storm Guard," “us,” “we,” or “our” throughout Stormguardrc.com collectively refers to both the Storm Guard brand and the Storm Guard Franchise System, which is made up almost exclusively of independently owned and operated franchise locations.
